MJS-CS-WH
Flexible Coupling -Jaw-type (Short) – Clamping Type
Dimension Drawing
Dimensions/Specifications/CAD
Part Number | A | L | W | B | C | F | G | M | Wrench Torque (N・m) |
---|---|---|---|---|---|---|---|---|---|
MJS-40CS-WH | 40 | 17 | 50 | 12 | 2 | 8.5 | 14 15.75 |
M5 M4 |
8 3.5 |
MJS-55CS-WH | 55 | 18 | 54 | 14 | 2 | 9 | 20 21 |
M6 M5 |
13 8 |
MJS-65CS-WH | 65 | 21 | 62 | 15 | 2.5 | 10.5 | 24 25 |
M8 M6 |
28 13 |
Part Number | Max. Bore Diameter (mm) | Rated Torque* (N・m) | Max. Torque* (N・m) | Backlash Zero Allowable Transmission Torque(N・m)*** | Max. Rotational (min-1) | Static Torsional Stiffness (N・m/rad) | Max. Lateral Misalignment (mm) | Max. Angular Misalignment (°) | Max. Axial Misalignment (mm) | Sleeve Hardness | Mass** (g) |
---|---|---|---|---|---|---|---|---|---|---|---|
MJS-40CS-WH | 25 | 10 | 20 | 1.2 | 15000 | 570 | 0.1 | 1 | 0~+1.2 | A92 | 100 |
MJS-55CS-WH | 32 | 35 | 70 | – | 11000 | 1600 | 0.15 | 1 | 0~+1.4 | A92 | 210 |
MJS-65CS-WH | 38 | 95 | 190 | – | 9000 | 3000 | 0.15 | 1 | 0~+1.5 | A92 | 340 |
* Correction of rated torque and max. torque due to load fluctuation is not required.However, if ambient temperature exceeds 30°C, be sure to correct the rated torque and max. torque with temperature correction factor shown in the table.MJC’s allowable operating temperature is -20°C to 60°C.
** These are values with max. bore diameter.
*** For transmission of backlash0Zero, please use a tight fit sleeve.
Part Number | Stock Bores D1-D2 | ||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
8 | 9.525 | 10 | 11 | 12 | 14 | 15 | 16 | 18 | 19 | 20 | 22 | 24 | 25 | 28 | 30 | 32 | 35 | 38 | |
MJS-40CS-WH | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | – | – | – | – | – |
MJS-55CS-WH | – | – | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | – | – |
MJS-65CS-WH | – | – | – | – | – | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● | ● |
All products are provided with hex socket head cap screw.
Recommended dimensional allowances of applicable shaft diameter are h6 and h7.
A set of hubs with clamping type for one side and clamping + key type for the other side is available upon request.
In case of mounting on D-cut shaft, be careful about the position of the D-cut surface of the shaft.
Material/Finish
MJS-CS/MJS-CSK | |
---|---|
Hub | A2017 Alumite Treatment |
Sleeve | Polyurethane |
Hex Socket Head Cap Screw | SCM435 Ferrosoferric Oxide Film (Black) |
Structure
Clamping Type MJS-CS-BL,MJS-CS-EBL,MJS-CS-EGR,MJS-CS-ERD,MJS-CS-EWH,MJS-CS-GR,MJS-CS-RD,MJS-CS-WH
MJS-**CS-**Tight Fit
MJS-**CS-E**Easy Fit
Clamping + Key Type MJS-CSK-BL,MJS-CSK-EBL,MJS-CSK-EGR,MJS-CSK-ERD,MJS-CSK-EWH,MJS-CSK-GR,MJS-CSK-RD,MJS-CSK-WH
MJS-**CSK-**Tight Fit
MJS-**CSK-E**Easy Fit
Sleeve
Characteristics
- Applicable motors
Tight Fit Easy Fit Servomotor ◎ ○ Stepping Motor ◎ ◎ General-Purpose Motor ◎ ◎ ◎: Excellent ○: Very good
- Property
Tight Fit Easy Fit Zero Backlash ○ – High Torque ◎ ◎ Allowable Misalignment ○ ○ Vibration Absorption ◎ ◎ Electrical Insulation ◎ ◎ Assembling ○ ◎ Allowable Operating Temperature -20℃ to 60℃ -20℃ to 60℃ ◎: Excellent ○: Very good
- This is a jaw type flexible coupling.
- It is a short type and more compact than MJC.
- Tight Fit enables transmission with zero backlash at low torque.
- Easy fit allows assembling and separation of hubs.
- Excellent flexibility allows eccentricity, angular misalignment and twisting vibration to be accepted.
- It has electrical insulation. Resistance value: Not less than 2 MΩ
- Sleeve Type
Selection
The area bounded by the shaft diameter and rated torque indicates is the selection size.
Selection example
In case of selected parameters of shaft diameter of φ15 and load torque of 6 N•m, the selected size for MJS-**CS-RD, MJS-**CS-ERD is MJS-40CS-RD, MJS-40CS-ERD.
Ambient Temperature / Temperature Correction Factor
Ambient Temperature | Temperature Correction Factor |
---|---|
-20℃ to 30℃ | 1.00 |
30℃ to 40℃ | 0.80 |
40℃ to 60℃ | 0.70 |
Sleeve Details
Tight Fit
The hub and sleeve are press-fit and can be used under zero backlash*.Since the sleeve’s vibration absorption can raise the gain of a servomotor, this unit can achieve high responsive operation exceeding the Disk coupling.
*For the torque used under zero backlash, please refer to Performance table.
Easy Fit
This unit allows you to easily assemble and partition the hub and sleeve.
This allows you to reduce the time of assembling the unit and maintenance.
It is possible to mount a hub on the shaft in advance and easily assemble the unit even in a location where the coupling is less-visible.
Slip Torque
Concerning the sizes shown in the table, please note that the shaft’s slip torque is smaller than the max. torque of MJS-CS.
Part Number | Bore Diameter (mm) | ||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
8 | 9.525 | 10 | 11 | 12 | 14 | 15 | 16 | 18 | 19 | 20 | 22 | 24 | 25 | 28 | 30 | 32 | 35 | 38 | |
MJS-40CS | 28.9 | 35.6 | 37.7 | ||||||||||||||||
MJS-55CS | 40.2 | 46.7 | 53.2 | 66.1 | 72.6 | 79 | 92 | 98.4 | 104 | 117 | 130 | 137 | 145 | ||||||
MJS-65CS | 113 | 123 | 134 | 155 | 165 | 176 | 197 | 218 | 228 | 260 | 281 | 302 | 300 | 300 |
These are test values based on the condition of shaft’s dimensional allowance: h7, hardness: from 34-40 HRC, and screw tightening torque of the values described in MJS-CS dimensional table.
Change in static torsional stiffness due to temperature
This is a value under the condition where the static torsional stiffness at 20°C is 100%.
The change of torsional stiffness within the range of allowable operating temperature is as shown in the graph.
Before using the unit, be aware of the deterioration of responsiveness.
Eccentric Reaction Force